craftsman limited edition table saw manual

craftsman limited edition table saw manual

Page Count: 62 Safety Instructions. Assembly ? Operation ? Maintenance ? Parts List Crystalline silica from bricks, cement and other masonry products, and. Arsenic and chromium from chemically treated lumber. Y our risk from these exposures varies, depending on how often you do this type of work. T o reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to ?lter out microscopic particles. A void prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals. With proof of purchase, a defective product will receive free repair or replacement at option of seller. This ONE Y EAR war rant y i s vo id if t his pro duc t is eve r us ed whil e pr ovi ding co mmer cia l se rvi ces or if r ent ed t o a noth er pers on. For 90 DA Y com merc ial and ren tal use te rms, se e th e C raft sma n wa rra nty web pag e. This w arr anty gi ves you spe ci.Sears Brands Management Corporation, Hoffman Estates, IL 60179 Universal Ampere. 15 Amp V oltage. 120 V AC Hz. 60 Hz RPM (no load). 5000 RPM (No load) Overload Protection. This tool is wired at the factory for 1 10-120 V olt operation. T o avoid shock or ?re, replace power cord immediately if it is worn, cut or damaged in any way. Before using your tool, it is critical that you read and understand these safety rules. Failure to follow these rules could result in serious injury to you or damage to the tool. Shown below are some of the symbols you may see. DANGER ? ! W ARNING ? ! CAUTION ? ! CAUTION DANGER: indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.http://ateliersmq.com/pevron/www/img/canon-mp-90-user-manual.xml

• 1.0.

W ARNING: indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION: indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. CAUTION: used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage. SYMBOLS SAFETY ALERT: Precautions that involve your safety. PROHIBITION WEAR EYE PROTECTION: Always wear safety goggles or safety glasses with side shields. READ AND UNDERST AND INSTRUCTION MANUAL: T o reduce the risk of injury, user and all bystanders must read and understand instruction manual before using this product. SUPPORT AND CLAMP WORK KEEP HANDS A W A Y FROM BLADE: Failure to keep your hands away from the blade will result in serious personal injury. WEAR RESPIRA TOR Y AND HEARING PROTECTION: Always wear respiratory and hearing protection. LEARN the tool’s application, limitations and possible hazards. 2. KEEP GUARDS IN PLACE and in working order. 3. REMOVE ADJUSTING KEYS AND WRENCHES. Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning ON. 4. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 5. DO NOT USE IN DANGEROUS ENVIRONMENTS. Do not use power tools in damp locations, or expose them to rain or snow. Keep work area well lit. 6. KEEP CHILDREN A W A Y. All visitors and bystanders should be kept a sa fe distanc e from wor k area. 7. MAKE WO RKSH OP CH ILD PROO F with padlocks, mast er switches or by removing starter keys. 8. DO NOT FORCE THE TOOL. It will do the job better and safer at the rate for which it was designed. 9. USE THE RIGHT T OOL. Do not force the tool or a n attachment to do a job for which it was not designed. 10. USE PROPER EXTENSION CORDS. Make sure your extension cord is in good condition.http://debschoen.com/userfiles/canon-mp-850-manual.xml

When using an extension cord, be sure to use the one heavy enough to carry the current that the product will draw. An undersized cord will result in a drop in line voltage and in loss of power which will cause the tool overheat. The table on page 13 shows the proper wire gauge size usage to each ext ension cord length and ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.Nonslip footwear is recommended. Wear protective hair covering to contain long hair. 12. AL W A YS WEAR EYE PROTECTION. Any power tool can throw foreign objects into the eyes and could cause permanent eye damage. They ARE NOT safety glasses. Safety Goggles are available at Sears. NOTE: Glasses or goggles not in compliance with ANSI Z87.1 could seriously injure you when they break. 13. WEAR A F ACE MASK OR DUST MASK. Sawing operation produces dust. 14. SECURE WORK. Use clamps or a vice to hold work when practical. It is safer than using your hand and it frees both hands to operate the tool. 15. DISCONNECT TOOLS FROM POWER SOURCE before servicing, and when changing accessories such as blades, bits and cutters. 16. REDUCE THE RISK OF UNINTENTIONAL ST ARTING. Make sure switch is in the OFF position before plugging the tool in. 17. USE RECOMMENDED ACCESSORIES. Consult this Operator ’s Manual for recommended accessories. The use of improper accessories may cause risk of injury to yourself or others. 18. NEVER ST AND ON THE TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted. 19. CHECK FOR DAMAGED P ARTS. A guard or other part that is damaged should be properly repaired or replaced. 20. NEVER LEA VE THE TOOL RUNNING UNA TTENDED.NEVER reach across the path of the cutting blade while tool is in operation. 22. MAINT AIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 23. DO NOT use power tool in p resence of ?

ammable liquids or gases. 24. DO NOT operate the tool if you are under the in?uence of any drugs, alcohol or medication that could affect your ability to use the tool properly. 25. Dust generated from certain materials can be hazardous to your health. Always operate saw in well- ventilated area and provide for proper dust removal. 26. People with electronic devices, such as pacemakers, should consult their physician(s) before using this product. Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker. 27. WEAR HEARING PROTECTION to reduce the risk of induced hearing loss.Refer to ripping instru ctions in th is Ope rator’s Ma nual where the push stick is covered in detail. A pattern for making your own push stick is included on page 56. 4. NEVER PERFORM ANY OPERA TION FREEHAND, which means can using hands to support the workpiece, but always use either the fence OR the miter gauge to position and guide the workpiece. NEVER USE THE MITER GAUGE AND FENCE SIMUL T ANEOUSL Y. 5. NEVER ST AND or have any part of your body in line with the path of the saw blade. Keep your hands out of the saw blade path. 6. NEVER REACH behind or over the cutting tool for any reason. 7. REMOVE the rip fence when crosscutting. 8. DO NOT USE a molding head with this saw. 9. DIRECTION OF FEED. Feed work into a blade against the direction of rotation of the blade. 10. NEVER use the rip fence as a cut-off gauge when crosscutting. 1 1. NEVER A TTEMPT TO FREE A ST ALLED S A W BLAD E witho ut ?rs t turning the saw OFF. T urn power switch OFF immediately to prevent motor damage. 12. PROVIDE ADEQUA TE SUPPORT to the rear and the sides of the saw table for long or wide workpieces. 13. A VOID KICKBACKS (work thrown back towards you) by keeping the blade sharp, the rip fence parallel to the saw blade and by keeping the riving knife, anti-kickback pawls assembly and guards in place, aligned and functioning.

Do not release work before passing it completely beyond the saw blade. Do not rip work that is twisted, warped or does not have a straight edge to guide it along the fence. Do not attempt to reverse out of a cut with the blade running.Solvents could possibly dissolve or otherwise damage the material. Only a soft damp cloth should be used to clean plastic parts. 16. MOUNT your table saw on a bench or stand before performing any cutting operations. Refer to ASSEMBL Y on page 20. Secure tool properly to prevent unexpected movement. 17. Never cut metals or masonry products with this tool. This table saw is designed for use on wood and wood-like products only. 18. AL W A YS USE IN A WELL- VENTILA TED AREA. Remove sawdust frequently. Clean out sawdust from the interior of the saw to prevent a potential ?re hazard. Attach a vacuum to the dust port for additional sawdust removal. 19. NEVER LEA VE THE SA W RUNNING UNA TTENDED. Do not leave the saw until the blade comes to a complete stop. 20.For proper operation follow the instructions in this Instruction Manual entitled ASSEMBL Y AND ADJUSTMENTS (Page 20). Failure to provide sawdust fall-through and removal hole will allow sawdust to build up in the motor area resulting in a ?re hazard and potential motor damage. 21. USE ONL Y saw blades recommended with the warning that the riving knife shall not be thicker than the width of the groove cut by the saw blade and not thinner than the body of the saw blade. 22. USE PUSH-STICK OR PUSH BLOCK to feed the workpiece past the saw blade. The push-stick or push block should always be stored with the machine when not in use.The riving knife is a ?at plate that ?ts into the cut made by the saw blade and effectively ?ghts kickback by lessening the tendency of the blade to bind in the cut. The blade guard assembly and anti- kickback assembly can only be used when making through cuts that sever the wood.

When making rabbets and other cuts that make non through cuts, the blade guard assembly and anti- kickback assembly must be removed and riving knife lowered to the non through cut position marked on the rivi ng knif e. T wo an ti- kick back paw ls are located on the sides of the riving knife that allow the wood to pass through the blade in the cutting direction but reduce the possibility of the material being thrown backwards toward the operator. Use all components of the guarding system (blade guard assembly, riving knife and anti-kickback assembly) for every operation for which they can be used including all through cutting. If you elect not to use any of these components for a particular application exercise additional caution regarding control of the workpiece, the use of push sticks, the position of your hands relative to the blade, the use of safety glasses, the means to avoid kickback and all other warnings contained in this manual and on the saw itself. Replace the guarding systems as soon as you return to thru-cutting operations. Keep the guard assembly in working order. KIC KBA CKS KIC KBA CKS: K ick bac ks can ca use ser iou s i nju ry. A ki ckb ack oc cur s w hen a p art of th e w ork pie ce bin ds bet wee n the sa w b lad e a nd the ri p f enc e, or oth er ?xe d o bje ct, an d r ise s f rom th e tab le and is th row n t owa rd the op era tor. Kic kba cks ca n b e a voi ded by at ten tio n to the fo llo win g c ond iti ons. How to Avoid Kickbacks and Protect Y ourself from Possible Injury: a. Be certain that the rip fence is parallel to the saw blade. b. Do not rip by applyin g the feed force to the section of the workpiece that will become the cut-off (free) piece. Feed force when ripping should always be applied between the saw blade and the fence; use a push stick for narrow work, 6 in. (152 mm) wide or less. c. Keep saw blade guard assembly, riving knife and anti-kickback assembly in place and operating properly.

If anti-kickback assembly is not operational, return your unit to the nearest authorized service center for repair. The riving knife must be in alignment with the saw blade and the anti-kickback pawls assembly must stop a kickback T ABLE SA W SAFETY Check their action before ripping by pushing the wood under the anti-kickback assembly. The teeth must prevent the wood from being pulled toward the front of the saw. d. Plastic and composite (like hardboard) materials may be cut on your saw. However, since these are usually quite hard and slippery, the anti-kickback pawls may not stop a kickback.Use a seperate electrical circuit for your tool. Y our table saw is wired at the factory for 120 V operation. Connect to a 120 V, 15 Amp circuit and use a 15 Amp time delay fuse or circuit breaker. T o avoid shock or ?re, if power cord is worn, cut, or damaged in any way, have it replaced immediately. GROUNDING INSTRUCTIONS This tool must be grounded while in use to protect the operator from electrical shock. IN THE EVENT OF A MALFUNCTION OR BREA KDOWN, groundi ng provi des a path of least resistance for electric currents and reduces the risk of electric shock. This tool is equipped with an electrical cord that has an equipment grounding conductor and a grounding plug. The plug must be plugged into a matching receptacle that is properly installed and grounded in accordance with all local codes and ordinances.The conductor with the green insulation (with or without yellow stripes) is the equipment grounding conductor. If repair or replacement of the electrical cord or plug is necessary, do not connect the equipment grounding conductor to a live terminal. CHECK with a quali?ed electrician or service person if you do not completely understand the grounding instructions, or if you are not certain the tool is properly grounded. USE only 3-wire extension cords that have three-pronged grounding plugs with three-pole receptacles that accept the tool’ s plug.

Repair or replace damaged or worn cords immediately. Use a separate electrical circuit for your tool. Before connecting the motor to the power line, make sure the switch is in the off position and the electric current is rated the same as the current stamped on the motor nameplate. Running at a lower voltage will damage the motor.Use an extension cord heavy enough to carry the current your product will draw. draw. An undersized cord will cause a drop in line voltage resulting in loss of power, W ARNING.In all cases, make certain the receptacle is properly grounded. If you are not sure, have a quali?ed electrician check the receptacle.The table below shows the correct size to use depending on cord length and nameplate ampere rating. The smaller the gauge number, the heavier the cord. GUIDELINES FOR EXTENSION CORDS Make sure your extension cord is properly wired and in good condition. Always replace a damaged extension cord or have it repaired by a quali?ed technician before using it. Protect your extension cords from sharp objects, excessive heat and damp or wet areas. This tool is for indoor use only. Do not expose to rain or use in damp locations. This tool is intended for use on a circuit that has a receptacle like the one illustrated in Fig. 1. Fig. 1 shows a three-pronged electrical plug and receptacle that has a grounding conductor. If a properly grounded receptacle is not available, an adapter (Fig. 2) can be used to temporarily connect this plug to a two-contact grounded receptacle. MI NI MU M GA UGE F OR E XTEN SIO N CO RD S (A WG ) (When usng 120 volts only) Ampere Rating T otal length of Cord Mo re T han N ot M ore Th an 25ft. 50ft. 100ft. 150 ft. ( 7.62 15.24 30.48 45.72 m ) A WG- Amer ican W ire Ga uge 0 6 18 16 16 14 6 10 18 16 14 12 10 12 16 16 14 12 12 16 14 12 No t Reco mme nd ed W ARNING. CAUTION ? ! Three-Pronged Plug Grounding Prong Properly Grounded Three-Pronged Receptacle Fig. 1 Fig.

2 Grounding Lug Make sure this is connected to a known ground. T wo-Pronged Receptacle Adapter Call 1-800-843-1682 for missing or damaged parts. Separate all parts from packing materials. Check each part with the illustration on the next page and the “T able of Loose Parts” to make certain all items are accounted for, before discarding any packing material. NOTE: T o make assembly easier, keep contents of box together.It helps make accurate straight or angle crosscuts.When dado cutting, a dado insert plate must be used. NOTE: Bla de gua rd ass emb ly is rem oved for pur po ses o f i ll ust ra tio n onl y. Do not resaw material with this saw. Slightly thinner than the saw blade, it helps keep the kerf open and prevents kickback. W ARNING ! Leading edge Kerf Surface Saw blade path T railing edge W orkpiece Direction of workpiece Refer to the parts list for correct quantities. 2. Attach four hooks (10) to the top corner of the four legs (2) as shown. The hooks (10) are used to hold the dust bag. NOTE: Make sure the hook (10) is securely fastened to the corner of the leg (2). 3. Attach one long upper support (1) to top of leg (2) using one bolt (3) and nut (4). Only hand-tighten support attachment bolts until stand is fully assembled. NOTE: ? Align detents (8) in stand leg with support brackets to ensure proper ?t. ? Do not fully tighten bolts until stand is properly aligned. ? Position all supports to the INSIDE of the leg assembles. 4. Attach short upper supports (6) to other hole of leg (2) using one bolt and nut. Fig. A 5. Assemble the other upper supports in exactly the same manner. 6. Attach one bottom support (5) to the center of the leg using bolt (3) and nut (4). This completes the front frame section. 7. Assemble rear frame section in exactly the same manner. 8. Joi n f ron t-b ott om and re ar- bot tom fra me ass emb lie s u sin g t he bot tom sup por t ( 7), bo lts an d n uts. Fig. B 10 2 10 6 2 3 4 10 8 1 Fig. C Front 7 5 1 6 2 Fully T ighten the nut. 4.

At tac h t he rol ler wh ee l (14 ) t o r oll er wh eel br ack et (1 1), bo lt (15 ) a nd loc k nu t ( 16) us ing sq uar e ne ck bol t ( 15) an d l ock nu t ( 16) as s ho wn. NOTE: Do not overtighten lock nut as this will not allow the wheels to turn. 5. Rep eat st eps 1- 4 f or lef t r ear le g ( 17) and roller wheel assembly. NOTE: The roller wheel assemblies and bottom support bracket (18) can be installed on either the right- hand side or left-hand side. Always install the roller wheel assemblies and the bottom support bracket (18) at the same time. The illustration shows the roller wheels on the left- hand side. Fig. D 12 13 14 15 16 2 1 1 18 6. Carefully set the stand in its upright position on a clean level surface. ASSEMBLING THE FOOT P AD TO ST AND (FIG. F) 1. Place all four foot pads (9) onto each leg. 2. Place stand on level surface and adjust so all legs are contacting the ?oor and are at similar angles to the ?oor, and detents in stand leg align with support brackets. Once stand is properly aligned, fully tighten all bolts. NOTE: Stand should not rock after all bolts are tightend. Fig. E 2 Front 18 17 Fig. F 9 9 NOT E: Y ou may ne ed to loo sen th e two sh ort su ppo rt bra cke ts if the two mo unt ing ho les ar e n ot lin ed up cor rec tly. Ret igh ten th ese bo lts on ce you ha ve add ed the le ver lo cks. 4. Attach the lock nuts (22) and tighten with an 8 mm or adjustable wrench. 5. Install the other locking lever assemblies in exactly the same manner. 6. Position the saw base on the stand. 7. Line up the lever lock cover (23) to the saw base and push down the locking lever (19). 8. Fa ste n s aw to sta nd us in g f our lo cki ng lev er ass emb li es (1 8). NOTE: The four locking lever assemblies (18) are provided for quick releasing the table saw from the stand. All four levers must be locked in the down position before operating saw. W ARNING ! 2 20 22 24 18 23 19 21 Fig.At ta ch the nu t a nd tig ht en us ing a 13 mm wre nch.

Re pea t f or ot her th ree co rne rs. SA W MOUNTED TO WORK SURF ACE (FIG. I) 1. If the leg set will not be used, the saw must be properly secured to a sturdy workbench using the four mounting holes at the base of the saw. 2. The surface of the table where the saw is to be mounted must have a hole large enough to facilitate sawdust fall-through and removal. Fig. H 25 26 27 25 26 27 The bracket will snap into place. W ARNING ! Fig. J 1 3 2 Fig. K 2 1 1 K) Storage brackets for the rip fence (2) and miter gauge (3) are located on the left side of the saw housing. Blade Wrench (Fig. L) Insert the blade wrench into the slot (4) located to the back side of the saw housing. Blade (Fig. M) 1. Loosen and remove the knob (1) on the right side of the saw housing. 2. Place extra blades (not included) onto the arbor. Replace the knob (1) and tighten. 4 Fig. L ASSEMBLING THE HANDWHEEL HANDLE (FIG. N) Thread the handwheel handle (1) into the handwheel hole, and then tighten the nut against the handwheel with a 14 mm or adjustable wrench. INST ALLING T ABLE SIDE EXTENSIONS (FIG. O) 1. Identify the right hand table extension. NOTE: For illustration purposes, the view in Fig. O looks “through” the saw table to the under side of the table. The right hand tab le exte nsion is the one with the measuring scale visible from the front of the saw when it is installed to the right hand side of the saw table. 2. Unlock both front and rear cam locking levers (1) on the right hand side of the saw base by ?ipping the levers over. 3. Insert the table extension mounting tubes (2) into the two matching holes in the cam lever assemblies. NOTE: Make sure the front mounting tube has the measuring scale visible from the front of the saw. Fig. M 1 Fig. N 1 See page 42. 7. Make sure the screw (3) into the matching hole (4) of the extension mounting tube (2). 8. Install the left hand table extension the same manner. INST ALLING THE REAR OUTFEED SUPPORT (FIG. P, Q) 1.

Insert the two rear outfeed support tubes (2) into the rear outfeed support (1). (Fig. P) NOTE: They must be inserted into the back of the support with the dimple end last so that the bar will hold the support in place. 2. Snap two black plastic stops (3) over the two rear outfeed support tubes (2). Make sure the locating pin in the black plastic stops.This will “lock” the tube into the support. (Fig. P) 3. Insert rear outfeed support tubes (2) into the two holes in the rear of the saw table, and into the extension tube brackets under the table. Position the rear table support so that the instruction labels are facing up. (Fig. Q) 4. T ighten one rear outfeed support stop screw (4) on the end of the left rear outfeed support tube (2). V erify that the screw is fully inserted into the corresponding hole in the support tube. (Fig. Q) Fig. O 2 4 3 1 Fig. P 1 2 Dimple End 3 Fig.Lock the blade bevel lock knob.Lock the blade bevel lock knob. Clean but do not remove the inner blade ?ange before reassembling the blade. (Fig. T) INST ALLING THE RIVING KNIFE (FIG. W ARNING ! 1 2 Fig. U W ARNING ! Failure to maintain a level insert can result in serious injury to the operator. ? The lever can be pulled out to allow it to be turned to a new position downward. (Fig. W) cavity side face to lock lever 3 4 5 6 7 8 W ARNING ! Fig. V BL ADE GU ARD ASS EMB L Y (F IG. X, Y, Z, AA ) T o avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is disconnected from the power source outlet. ? When installing the blade guard, cover the blade teeth with a piece of folded cardboard to protect yourself from possible injury. ? Never operate this machine without the blade guard in place for all t hrough saw ing operat ions. Installing the blade guard and anti- kickback pawls assembly (Fig. Make sure the blade bevel lock knob is tight. 2. Rai se t he ri vin g kni fe ( 1) to i ts hi ghe st pos iti on (th rou gh cut po sit ion ).

T ake the an ti- kic kba ck paw ls ass emb ly and li ft up the lo cki ng lev er (2) loc ate d o n t op. (F ig. X) 3. Place the front of assembly into slot (3) and push down, making sure the assembly is engaged in the slot. Push down on the locking lever (2) to lock. (Fig. X, Y) NOTE: Make sure the anti-kickback pawls assembly is locked in position before operating saw. Fig. W 3 6 8 W ARNING ! Z 5 1 8 4 5 5 6 7 Press down W ARNING ! Do not release the work before passing it completely beyond the saw blade. Do not attempt to back out of a cut with the blade running. Improper riving knife alignment can cause “kickback” and serious injury.NO TE: Se e in st ru ct io ns o n AD JU ST IN G THE LA SER LI NE on 39. Fig. BB W ARNING ! Anti-kickback Pawls W ARNING ! Fig. CC 2 1 3 Never use a rip fence and miter gauge together. Fig. DD W ARNING ! 1 3 2 RIP FENCE ADJUSTMENT (FIG. FF) 1. The fence (1) is moved by lifting up on the handle (2) and sliding the fence to the desired location. Pushing down on the handle locks the fence in position. 2. Position the fence on the right side of the table and along the edge miter gauge groove. 3. Lock the fence handle. The fence should be parallel with the miter gauge groove. Fig. EE 4. If adjustment is needed to make the fence parallel to the groove, do the following. Loosen the two bolts (3) and lift up on the handle (2). ? Hold the fence bracket (4) ?rmly against the fr ont of t he saw table. Move the fence until it is parallel with the miter gauge groove. Push the handle down and tighten both bolts. 5. If fence is loose when the handle is in the locked (downward) position, do the following. Move the handle (2) upward and turn the adjusting nut (5) clockwise until the rear clamp is snug. Failure to properly align fence can cause “kickback” and serious injury. W ARNING ! Fig. FF 5 1 3 4 2 The s cal e sho ws the di sta nce fr om the si de of the fe nce to ne are st si de of the bl ade. 2. Measure the actual distance with a rule.

If there is a difference between the measurement and the indicator, adjust the indicator (1). 3. Loo sen th e s cre w ( 2) and sl ide th e ind ica tor to th e c orr ect me asu rem ent on the sc ale. T igh ten th e s cre w a nd rem eas ure wi th the ru le. T o a voi d i nju ry fro m a n a cci den tal st art, m ake su re the s wi tch is in th e OF F p osi tio n a nd the p lu g i s n ot co nne cte d t o t he pow er s our ce out let. ADJUSTING THE MITER GAUGE (FIG. HH) 1. Loosen the lock handle (1) to allow the miter body (2) to rotate freely. T ighten the lock handle to hold the miter body in position. 1 2 W ARNING ! Fig. GG 2. If the po int er (3) re qui res ad jus tme nt, loo sen th e s cre w u nde r t he poi nte r wit h a sc rew dri ver.If the table insert is not ?ush with the table, adjust the two bolts (1) with a 4 mm hex wrench until it is parallel with the table. NOTE: T o raise the insert, turn the hex screws counterclockwise, to lower the insert, turn the hex screws clockwise. Do not remove the insert, adjustments need to be made with the insert in place to get the proper level. Fig. HH 3 1 2 W ARNING ! Measure for exactness.Always disconnect plug from the power source when making any adjustments. ? Inaccurate adjustment can result in kickback and serious personal injury.If not or the base of the rule is no longer parallel with the edge of the miter gauge groove, see adjustment procedure described in next section.ALI GNI NG THE RI VIN G K NIF E (FI G. OO) ? T o avoid i njury f rom an a ccident al start, make sure the switch is in the OFF position and the plug is disconnected from the power source outlet. ? Never operate this tool without the riving knife in the correct position. ? Never operate this tool without the blade guard in place for all through sawing operations. ? Thi s a dju stm ent wa s m ade at th e fa ct ory, b ut i t sh oul d be rec he ck ed and ad jus ted if ne ces sar y. Fig. NN W ARNING ! 3 1 2 If unquali?

ed persons attempt to repair this laser product, serious injury may result. Any repair required on this laser product should be performed by authorized se rvice center pe rsonnel. ? Laser W arning Label: LASER RADIA TION-A VOID DIRECT EYE EXPOSURE. Max. Output:, W avelength: 630-660 nm, Complies with 21 CFR 1040.10 and 1040.1 1 Class IIIa Laser Product. ( Fig. PP ) ? Laser Aperture Label: A VOID EXPOSURE: Laser radiation is emitted from this aperture. (Fig. PP) The laser beam is emitted when the laser line is turned on. Do not stare into the beam or view it directly using optical instruments. Do not remove the warning label that is af?xed to the blade guard. Avoid aiming the laser beam directly into the eyes. ? A laser beam is not a toy, and it should not be used by children. Do not look directly into the laser beam. ? If the Laser Line will not be used for more than three months, remove the batteries in order to avoid damage from possible leakage. ? The laser line does not include any user-serviceable components. Do not open the housing in an attempt to repair it. ? Repair s should o nly be car ried out a t a service center or by an authorized service technician. ? NOTE: All the adjustments for the operation of this machine have been completed at the factory. Due to normal wear and use, some occasional readjustments may be necessary.D o n ot sta re in to bea m o r l ook di re ct ly at it usi ng op tic al ins tru men ts. D o not re mov e th e w arn ing la bel th at i s a f?x ed to the bl ade gu ard. D o n ot di re ct the la ser in to the ey es. NOTE: All of the adjustments for the operation of this machine have been carried out at the factory. Occasional readjustments may be necessary as a result of normal wear and use. 1. T urn the laser guide on. Place a straight edge or ruler against the right side of the blade. 2. V erify wh eth er the la ser li ne is ?us h aga ins t t he rig ht sid e o f t he bla de, and ag ain st the st rai ght ed ge or rul er. 3.